Escea DL1100 Manual de Instalação

630185_6 IB Installation Manual AU IB1100 and IB850 (Log Fire / Coal Fire) Installation Manual AUSTRALIAN EDITION Important: The

630185_6 IB Installation Manual AU 10 9.0 Corner Installations: If a cavity is to be created in a corner, the following drawings give the minimum s

630185_6 IB Installation Manual AU 11 The electrical cord (from an extension cord) should pass through the Outer Skin Kit as shown, through the supp

630185_6 IB Installation Manual AU 12 11.0 Flue Systems Non-Masonry Timber Frame Cavity: The heater must be flued to the outside via a 100mm diamet

630185_6 IB Installation Manual AU 13 11.1 Other Flue Kits- (Glen Dimplex kits only shown. Check with local distributor for availability) 552327 St

630185_6 IB Installation Manual AU 14 12.0 Installing the Flue System: Non-Masonry Timber Frame Cavity: The heater must be flued to the outside via

630185_6 IB Installation Manual AU 15 6. Fix an appropriate weather shielding to the outer liner at the penetration and seal to the roof or chimney

630185_6 IB Installation Manual AU 16 12.2 The top of the flue must be capped with an appropriate and approved anti down draft cowl. Note: As per n

630185_6 IB Installation Manual AU 17 FROM AS5601, please ensure compliance to all other relevant sections of this code. 2.6.13 FLUE TERMINALS 2.6

630185_6 IB Installation Manual AU 18

630185_6 IB Installation Manual AU 19 12.4 Fixing the Flue to the Cavity A length of angle should be attached to the inside of the timber frame ca

630185_6 IB Installation Manual AU 2 Note: THERE ARE A FEW THINGS TO CONSIDER BEFORE INSTALLATION  Cavity Dimensions, Clearances, and fitting the

630185_6 IB Installation Manual AU 20 12.5 Masonry Cavity and Chimney: The heater can be flued with 100mm flexible aluminum ducting in accordance w

630185_6 IB Installation Manual AU 21 13.3 It is recommended that a gas isolating valve be installed as close to the regulator on the

630185_6 IB Installation Manual AU 22 14.3 Attach the Top-Rear: Attach the top-rear panel to the Sides and Rear panels, with the flanges of the Top-

630185_6 IB Installation Manual AU 23 16.0 Gas Fireplace Installation: Attached to the base of the Outer Skin Kit are guide rails. The inside edge

630185_6 IB Installation Manual AU 24 Step 3: Remove the top of the heater outer shell. Take out the screw from each side (as shown below), lift a

630185_6 IB Installation Manual AU 25 17.0 Attaching the Flue to the Fireplace: Once the gas fireplace has been inserted into the OSK a

630185_6 IB Installation Manual AU 26 Note: Refer to 13.2 for further gas pipe laying information as per diagram below 19.0 Fix

630185_6 IB Installation Manual AU 27 19.2 Fixing Heater to Wall: The installer must also fix the heater to the sides of the cavity using the bracke

630185_6 IB Installation Manual AU 28 20.0 Placing the fuel bed: After replacing the firebox (if removed in 16.1) the fuel bed media can now be pl

630185_6 IB Installation Manual AU 29 IB850 Log & Template Position 4) Line up some of the coals that have been supplied with thi

630185_6 IB Installation Manual AU 3 Contents: Section:  Product Description 1.0  Creating the Cavity

630185_6 IB Installation Manual AU 30 20.2 IB1100: Locating the Log Set After Replacing the Firebox: 1) Remove packaging from around log sets 2)

630185_6 IB Installation Manual AU 31 20.3 Placing ceramic coal fuel beds: Spread the supplied ceramic stones evenly across the firebox base as s

630185_6 IB Installation Manual AU 32 Step 5: Replace the firebox by reversing the instructions in section 17.0 of this manual (do not replace th

630185_6 IB Installation Manual AU 33 Step 6: Replace the firebox by reversing the instructions in section 17.0 of this manual (do not replace the g

630185_6 IB Installation Manual AU 34 23.0 Gas Type Conversion: Your gas fire has been supplied with the necessary parts for gas conversion. F

630185_6 IB Installation Manual AU 35 23.5 Step 5: If changing from Propane to NG, slide the supplied burner collar onto the burner tubes of b

630185_6 IB Installation Manual AU 36 24.0 Checking Operating Pressure: WARNING: The regulator that is supplied with the fire MUST NOT BE REMOVED.

630185_6 IB Installation Manual AU 37 25.0 Fitting the Fascia Panels: To avoid scratches or knocks to the fascia panels of this heater they must be

630185_6 IB Installation Manual AU 38 25.1 When installing a 4 sided fascia ensure that the clips that the outer fascia screw into are at the bottom

630185_6 IB Installation Manual AU 39 27.0 Normal Operating Sounds and Smells; Note: Each time the fire is lit from cold the glass may fog up with

630185_6 IB Installation Manual AU 4 1.0 Product Description: The Escea IB1100 and IB850 gas fires are designed to be built into a cavity. Both appl

630185_6 IB Installation Manual AU 40 28.0 Installation Check List: 1 Ensure there is adequate ventilation in the area the applia

630185_6 IB Installation Manual AU 41 29.0 Escea Product Warranty 1 This document sets out the express warranties that apply in respect of Escea p

630185_6 IB Installation Manual AU 42 3 Warranty exclusions This express warranty does not apply where: (a) the Escea product has been installed,

630185_6 IB Installation Manual AU 43 6 Warranty claims If you make a valid claim under a parts and labour warranty and none of the exclusions set o

630185_4 IB Service Manual AU 12

630185_4 IB Service Manual AU 12

630185_4 IB Service Manual AU 11 Wiring Diagram IB850: Wiring Diagram IB1100: iPart No. 620125_318VAC240VACiPart No. 620140_318VAC240VAC

630185_4 IB Service Manual AU 10 Annual service procedure: 1. Isolate power to fire. 2. Remove front glass and clean inside of glass. 3. Remove lo

630185_4 IB Service Manual AU 9 Replacing Over-Temperature Cutout Devices: There are 2 Over-Temperature cut-out devices on this appliance; - One c

630185_4 IB Service Manual AU 8 IB850& IB1100Replacing Electronic Drawer / Components ISOLATE THE POWER TO THE FIRE BEFORE PROCEDURE. All of the

630185_6 IB Installation Manual AU 5 1.2 Product Dimensions IB850 Velo (3 sided) Velo (4 sided) Q

630185_4 IB Service Manual AU 7 Removing / Cleaning Fan or Replacing Firebox As part of regular service procedure, it is recommended that the fan is

630185_4 IB Service Manual AU 6 Checking Operating Pressure: This is done at the regulator located at the front RH corner of the appliance. This is b

630185_4 IB Service Manual AU 5 Cleaning the Fascia, Log Set and Glass: NEVER RUB THE FASCIA. The outside of the fascias must only be cleaned with a

630185_4 IB Service Manual AU 4 Draught Diverter Bimetallic Trip In the unlikely event that the fans have stalled, and the snap disk on the lid of

630185_4 IB Service Manual AU 3 Error Codes: This gas fire has been designed to show error codes to help explain and identify any fault situation tha

630185_4 IB Service Manual AU 2 Contents: Page: Error Codes 3 Cleaning the Log Set and Glass 5 Checki

630185_4 IB Service Manual AU IB1100 and IB850 (Log Fire / Coal Fire) Service Manual AUSTRALIAN EDITION Important  This

630185_6 IB Installation Manual AU 6 IB1100 Velo (3 sided) Velo (4 sided) Quadrato Rado A 1360mm 1360mm 1367m

630185_6 IB Installation Manual AU 7 CAB2.0 Creating the Cavity: The dimensioned drawing below shows the size of opening that must be created to fit

630185_6 IB Installation Manual AU 8 Therefore excess = 40MJ/hr - 25.2 MJ/hr = 14.8 MJ/hr = 4.11 kW Wall Vent Opening = 4.11 x 500mm2 = 2055mm2 T

630185_6 IB Installation Manual AU 9 30030150100200Maintain a 30mm clearance around the fascia to ensure ease of fascia removal. NB: No clearance is